Showing results: 61 - 75 of 90 items found.
-
ERAVANT
Doppler radar measures the Doppler effect, or an increase or decrease in the frequency of sound, light, or other waves as the source and observer move toward or away from each other.
-
Sabin -
Acoustic Engineering
Sabin is a powerful CAD tool for room acoustics engineers. Based on statistical calculations, it determines the acoustical parameters of a user defined room, such as the reverberation time T60, the sound pressure level, and the RASTI as a measure of speech intelligibility. These parameters are updated dynamically, while the user is changing simulated sound sources and absorbing materials.
-
M+P International
Noise is increasingly the subject of new regulations for the protection of human health and safety as well as for improving the environment in general. As well as sound levels, the perceived sound quality of products from washing machines to vehicles is often an important part of the customer buying decision so must be considered during product development. m+p Analyzer for noise and vibration measurement and analysis provides a full range of capability for these applications. Real-time fractional octave filters satisfy all acoustic applications from simple sound pressure, sound power for equipment legislative requirements, intensity mapping to isolate sources to sound quality metrics for product refinement.
-
Objective Solutions, Inc.
The Automation Monitor is a diagnostic system for remote analysis and troubleshooting of semiconductor capital equipment. The monitor is capable of delivering synchronous streams from strategically located video cameras, sound devices and data sources on the equipment.
-
NUL-212 -
Neulog
This sensor has two modes of operation. In slow mode it can be used to measure sound-pressure level in decibels. In fast mode it can display waveforms of different sound sources such as tuning forks and wind-chimes so that period and frequency can be determined.
-
MB-2200M10 -
Ono Sokki
MB-2200M10 is an ultra compact and lightweight microphone that enables measurement in narrow spaces, where have been difficult to install, without giving influence to the sound field.Its compact and lightweight features make you possible to perform measurements in a limited space, such as multi-point measurement, and measurement near the sound source. As CCLD type, the MB-2200M10 can be connected to Ono Sokki’s FFT Analyzer or CCLD supported devices.
-
STM-1 -
ECO-TECH
Tapping Machine Type STM-1 is intended for measurements of acoustic insulation of ceiling in buildings. The unit fulfils Annex A of ISO 140-6/7. These parts of the standard require a tapping machine as a sound source for impact noise measurements. Type STM-1 is available with an optional remote control.
-
Argon ST
We design, develop and produce state-of-the-art SIGINT sensors that seek, exploit, identify, and locate sources of RF energy, underwater sound, light, heat and other complex phenomena. These sensors recognize threats, gather intelligence, and allow our customers to make informed, strategic response decisions.
-
Leakshooter -
Synergys Technologies
With the LEAKSHOOTER ultrasound can be accurately measured. This allows to deliver a diagnosis. High frequency sounds are more directional than low frequency. This facilitates the search for the source, even in the presence of ambient noise. By adding the vision and the photo to the ultrasonic measurement SYNERGYS TECHNOLOGIES with its LEAKSHOOTER has significantly advanced this inspection technique.
-
SONASCREEN® -
SONOTEC GmbH
The handheld acoustic camera SONASCREEN generates acoustic images from both the audible and ultrasound frequency range. The device locates sound sources in real time and displays the results immediately on the screen. Furthermore, the camera provides audible feedback through industrial headphones. We make ultrasound audible and visible.
-
DMTH4 -
Lectrosonics, Inc.
The DMTH4 integrates telephone lines, video codecs and external audio sources into the digital bus structure of DM Series processors so these sources operate as though they are another microphone or audio input in the sound system. The unit is much more than just a telephone interface. Instead, it is a complete DM Series digital matrix processor, with a 3-in/24-out digital matrix, automatic mixing and comprehensive signal processing on every input and output. In essence, it simply connects to telephone lines, video codecs and external audio sources instead of mic/line inputs and outputs and integrates seamlessly with DM Series matrix processors.
-
Qam -
QSources BVBA
The amplifier is DSP controlled, with a very straightforward operation. Included is a white/pink noise signal generator. The internal signal module provides low crest noise signals to be able to reach high power levels from sound sources or electromagnetic shaker. External input of signal is equally possible, with spectral linearisation or without. This can be used for music, RASTI or any other signal
-
Geosonic -
BioAge s.r.l.
An Infrasonic Array works like a sonic antenna, it is able to detect the magnitude and the source of sound waves. The Geosonic array is able to detect also pressure waves that the human ears can’t hear. A typical pressure wave is that generated by an explosion or by any physical phenomena (natural or human created) that generates an air pressure wave, which means that the Geosonic array can be used to detect a lot of phenomena, like:
-
MCP4725 -
SparkFun Electronics
You've always wanted to output analog voltages from a microcontroller, the MCP4725 is the DAC that will let you do it! The MCP4725 is an I2C controlled Digital-to-Analog converter (DAC). A DAC allows you to send analog signal, such as a sine wave, from a digital source, such as the I2C interface on the Arduino microcontroller. Digital to analog converters are great for sound generation, musical instruments, and many other creative projects!
-
BAS003 -
Larson Davis, Inc.
The BAS003 Source is designed to generate homogeneous sound fields using random noise in compliance with the following standards: Building acoustics (insertion loss, acoustic absorption area, etc: ISO 140-3, ASTM E90, ISO 140-5, ASTM E966). The BAS003 is typically used to generate a noise in a free-field for the evaluation of the transmission loss index of a façade. The available high-efficiency power amplifier, BAS002, is light and can be remotely controlled for easy use in the field.
